Crosley Radio Stereo System CR221 Solo User Manual

cr221Manual.qxd 8/30/05 1:41 PM Page 1  
I n s t r u c t i o n  
CR-221  
M a n u a l SOLO  
 
cr221Manual.qxd 8/30/05 1:41 PM Page 4  
W e l co m e  
Getting Start e d  
Thank you for purchasing the Crosley Radio CR221 Solo Tabletop  
Receiver. Before operating this unit, please read this manual  
thoroughly and retain it for future reference.  
Features  
AroundSound - Your Crosley Solo features our exclusive  
AroundSound design. Using a single, custom - designed driver, the  
Solo radio simulates surround sound, creating a warm, ambient tone,  
regardless of where you may be located with regards to the radio.  
4
1
Portable Audio Ready - Your Solo radio comes ready to play portable  
audio products, including mp3 players, satellite radio, gaming devices,  
cd players, walkmans, - basically anything with a headphone jack!  
5
6
2
3
About This Manual  
Instructions in this manual describe the controls and functions of the  
CR221  
Control Locators  
1. Tuner Dial  
Table of Contents  
Getting Started  
2. Function Knob  
3. Power Indicator  
4. Tuning Knob  
5. Volume Knob  
6. Tuning LED  
Control Locators  
Connector Locators  
Unpacking  
4
5
6
6
Set Up  
Basic Operation  
AM/FM Radio  
Portable Audio Ready  
Auxillary Output  
7
7
7
General  
Troubleshooting Guide  
Warranty Information  
8
9
4
 
cr221Manual.qxd 8/30/05 1:41 PM Page 6  
Getting Start e d  
Getting Start e d  
Unpacking  
1. Remove packing material from unit.  
Note: Save all packing materials.  
2. Remove plastic bag covering radio.  
3. Remove ties from AC to DC power adaptor.  
4. Remove supplied audio cable from plastic bag.  
Note: Save cable for portable audio component hookup.  
1
1220 East Oak Street  
Louisville, KY 40204 USA  
OUTPUT  
AUX IN HEADPHONE  
4
5
2
3
Set Up  
1. Unwind the AC to DC power adaptor.  
2. Plug AC end of the power cord into appropriate outlet.  
3. Plug the small end of the power adaptor into  
the Power Jack in the back of the unit.  
CONTROL LOCATORS  
1. Antenna  
2. Power Jack  
3. Aux OUT  
4. Aux IN  
5. Headphone jack  
6. AC to DC Adapter  
6
5
6
 
cr221Manual.qxd 8/30/05 1:41 PM Page 8  
Getting Start e d  
Getting Start e d  
AM/FM RADIO  
Auxillary OUTPUT cont.  
1. Turn the Function Knob to the desired tuning band.  
The Power Indicator will turn green to indicate the power  
is turned on.  
2. Rotate the Tuning Knob to select the desired station.  
The Tuning LED will appear brightest when the best signal is  
reached. Some weaker but listenable AM stations may not  
turn on the Tuning LED.  
3. For information on using the auxiliary input feature of a specific  
component, refer to the auxiliary input section in the instruction  
manual of the desired component.  
4. Turn the Function Knob to select the desired output; AM, FM,  
or AUX.  
Note: You can still listen to your Comet while using the aux out  
feature.  
3. Adjust the volume to the desired level by rotating the Volume Knob.  
4. Position the antenna for optimum reception.  
Troubleshooting Guide  
PORTABLE AUDIO READY  
There is no power  
1. Turn the function knob to “AUX”. Turn the volume to a lower level.  
2. Using the supplied male to male mini pin connector, connect  
one end to the AUX OUTPUT jack on the back of the unit.  
3. Turn on your portable audio device and set the volume  
on the device to approximately 10% of full volume.  
4. Plug the other end into an output or headphone jack on your  
external device.  
1. Make sure AC to DC power cord is plugged in  
at the wall and at the back of the unit.  
2. Check that the Function Knob is not in the OFF position.  
There is no sound  
1. Make sure the Function switch is not in the AUX position.  
5. Begin playback on your external device.  
The sound is distorted.  
Adjust the volume to your desired listening level on your SOLO.  
For more volume, increase the setting on your portable device.  
1. Adjust the tuner and/or antenna to improve the  
signal strength. Under certain circumstances, the  
reception may be improved by relocating the unit.  
2. When using the “Aux in” plug, turn off any eq settings  
on the portable device.  
Auxillary OUTPUT  
The Auxillary Output feature is designed to let you use your SOLO  
as an audio source for other components.  
1. Using the supplied mini pin connector, connect one end to the  
OUTPUT JACK (auxiliary output), on the back of your S O L O.  
2. Plug the other end into an auxiliary input jack on the desired  
component.  
3. Check the volume level of external device if listening to auxiliary input.  
It should be set as low as possible.  
Note: If the desired component does not have a mini pin input  
jack, a separate cable will be needed.  
7
8
 
 
cr221Manual.qxd 8/30/05 1:41 PM Page 12  
1220 East Oak Street  
Louisville, Kentucky 40204  
 

Craftsman Snow Blower 486248371 User Manual
Danby Microwave Oven DMW101KSSDD User Manual
Delta Electronics Power Supply CKI24H User Manual
Digital Spectrum Digital Photo Frame NV 800 User Manual
Dynex Flat Panel Television DX LCD32 User Manual
EarthQuake Log Splitter W2265 User Manual
Electro Voice Stereo Amplifier AP2600 User Manual
EXFO Photonic Solutions Div Trash Compactor FTB 5230 User Manual
Garland Oven 4522970 REV 1 User Manual
Global Machinery Company Drill GTX18250 User Manual